When you open and close your garage door, you want it to move smoothly and quickly. That won’t happen if you don’t replace the springs and cables when they break or become too weak from age. These small parts can also be an indication of a much bigger problem that could result in the failure of the entire system, such as a broken support bearing or a detached bracket. Fortunately, replacing the springs and cables is not very difficult. It will take about 3 hours total to complete this job with simple hand tools and some knowledge of mechanics. You may even be able to find replacement springs at your local hardware store instead of ordering them online. Read on for step-by-step instructions on how to install garage door springs and cables.
How To Install Garage Door Springs And Cables
1. Remove the old springs and cables
The first thing you need to do is remove the old springs and cables. To do this, you will need to remove two bolts from each side of the garage door. These bolts are located along the bottom of the door near where it meets the floor. You can use a ratchet wrench or a socket wrench to remove them, but make sure that you wear safety glasses and gloves when doing this task.
2. Inspect and clean garage door opener mechanism
After removing all of the bolts from your garage door, take a look at your garage door opener mechanism. This is where your old springs and cables are attached to the transmission unit in order to transmit motion from your garage door to your car’s rollers. You should inspect it for any signs of wear or damage that could indicate a problem with your systems, such as broken brackets or loose bearings. If you see any signs of damage, replace them right away! If everything looks good on your garage door opener mechanism, then move on to step 3!
3. Install new springs and cables
Once you have inspected your garage door opener mechanism, it’s time to install new springs and cables! To do this, you will need two replacement springs (they are different lengths) as well as two replacement cable assemblies (they have different lengths). Each spring has one bolt in it that needs to be removed in order for it to be installed properly; however, if you have trouble removing the bolt, then you can use a screwdriver to help.
4. Install springs and cables on garage door opener mechanism
Now that you have all of the parts that you need to install new springs and cables, it’s time to put everything together! Take the two replacement springs that you ordered and place them on one side of your garage door opener mechanism. Place one of the replacement cable assemblies on top of each spring and bolt it in place with a single bolt. Repeat this process for the other side of your garage door opener mechanism.
5. Test garage door opener mechanism after installing new springs and cables
Before replacing the old garage door springs and cables, make sure that everything works properly by opening your garage door! If everything is working properly now, then it’s time to replace those old springs and cables! Before doing this, make sure to remove all of your bolts from your garage door so that they don’t get damaged when you are trying to remove them later on in this process. If you can see any damage after inspecting your garage door opener mechanism (such as broken brackets or loose bearings), then it’s important to have a professional come out and repair these issues before proceeding with replacing your old parts!
6. Replace the garage door springs and cables
To replace your old garage door springs and cables, you will need to use a pair of pliers in order to remove the bolts from your garage door opener mechanism. Next, remove the new springs and cables from their packaging and place them on top of the bolts that are already installed in your garage door opener mechanism. Make sure that they are positioned correctly before attempting to bolt them in place with a single bolt! If you have any questions about how to do this correctly, then you should definitely contact a professional!
7. Test garage door opener mechanism after replacing new springs and cables
After replacing all of your parts, it’s important to make sure that everything works properly by opening your garage door! If everything is working properly now, then it’s time to replace those old springs and cables! Before doing this, make sure to remove all of your bolts from your garage door so that they don’t get damaged when you are trying to remove them later on in this process. If you see any damage after inspecting your garage door opener mechanism (such as broken brackets or loose bearings), then it’s important to have a professional come out and repair these issues before proceeding with replacing your old parts!
What To Know Before You Start Repairing
Know the parts of your garage door opener mechanism
Before you begin repairs, make sure that you know exactly what each part of your garage door opener mechanism is called. This will help make the repair process much easier!
Know exactly how to remove each part of your garage door opener mechanism
Before you begin repairs, make sure that you know exactly how to remove each part of your garage door opener mechanism. This will help make the repair process much easier!
Make a list of all parts that need replacing
Before beginning to replace any parts, it’s important to create a list of all of the parts that need replacing in order to properly perform this repair! It’s also important to note which types of bolts are used in order to secure these parts into place!
Determine if you have additional tools or supplies needed for this repair
In addition to knowing what parts need replacing, it’s also important to know if you have any additional tools or supplies needed for this repair before starting work! For example, some people may need a screwdriver in order to remove some screws from their garage door opener mechanism.
What’s the Difference Between Springs and Cables?
1. Springs
Spring is the metal coil that connects to the motor and is a part of your garage door opener mechanism. Springs are usually made out of steel, but they can also be made out of other materials. The spring connects to the motor and then wraps around a pulley that connects to the cable door opener.
2. Cables
A cable is a metal wire that runs through your garage door opener mechanism and pulls on the springs. When you open your garage door, a cable pulls on these springs, which opens up your garage door!
Summary
When you go to replace the springs and cables on your garage door, it’s important to remember that the two are related. While they are two different pieces, they are both responsible for lifting and lowering the door. While cables are made to be fast, they are also much less durable than their coiled counterparts. Springs are more durable and take longer to relax. However, they are also made to last a long time. When you need to replace them, you should make sure you get the same type of springs that were originally installed. This will ensure that your garage door operates safely and smoothly.
FAQ’s
Q: How do I know if my springs and cables are worn out?
A: As your garage door opener gets older, the springs may become worn out and need to be replaced. Springs need to be replaced when they are worn down to about 1/4 inch in thickness. If you can see the metal from the spring on both sides, then it’s time for a new spring!
Q: How many springs do I need?
A: It depends on your garage door opener mechanism. The number of springs will vary depending on which brand or model of garage door you have installed. There is no one-size-fits-all answer to this question, so it’s important that you contact a professional for this type of information!
Q: What’s the best way to remove my old springs?
A: The best way to remove your old springs is with a pair of pliers. Make sure that you take your time when removing these old springs because they can break easily if you aren’t careful! Once your old springs are removed, make sure that all of them are in the same place before replacing them. For example, if there were two sets of three coils installed in one place, then only replace those three coils with new ones! This will ensure that everything is put back exactly where it was so that all parts work together properly.
